"SURE" BRAND WIRE WOUND RESISTOR - SSA SERIES
SILICON COATED AXIAL LEAD TYPE - Professional Grade

Features:

• High Power to size ratio.
• High pulse load handling capabilities
• High temperature silicone coating with flame proof property.
• Non-inductive / Low inductive available on request
• Robust - Welded Construction
• Reliability against severity of environmental abuses.
• Instant Solder ability
• Resistant to Solvent
• Resistant to Alcohol
• ERTL type tested as per IS 8909

General Specifications

DESCRIPTION	SSA 01	SSA 02	SSA 2.5	SSA 04	SSA 06	SSA 09	SSA 12	SSA 15	SSA 20
Resistance (1) range , Series And tolerance (2) + 10 % + 5 %	E24 Series
	0.01 Ω - 0.05 Ω
	0.06 Ω - 100 KΩ
Rated dissipation at T amb = 70 0c	1 W	2 W	2.5 W	4 W	6 W	9 W	12 W	15 W	20 W
Temperature coefficient. (3)	R < 10Ω : 0 to + 600 ppm/ 0c R > 10Ω : - 80 to + 140 ppm/ 0c
Operating temperature	- 40 0c to + 200 0c
Basic specification	IEC60 115-1
Limiting voltage	√ (Pn x R)
Stability R/Rmax after: Load Climate tests Resistance to soldering heat Short time overload	> 5.0% + 0.1 W > 1.0% + 0.05 W > 0.5% + 0.05 W > 2.0% + 0.1 W

(1) Special resistive values available on request
(2) Tolerances, 0.5, 1, 3 and 10% available on request
(3) Temperature coefficient, 30, 50 and 90ppm/°C, available on request

Mechanical Data



Table 1. Mechanical data

PRODUCT	L	D	d
SSA01	12.0 + 1.5	4.5 + 0.5	0.80 + 0.03
SSA02	14.0 + 1.5	5.5 + 0.5	0.80 + 0.03
SSA2.5	16.0 + 1.5	5.5 + 0.5	0.80 + 0.03
SSA04	18.0 + 1.5	6.5 + 0.5	0.80 + 0.03
SSA06	26.0 + 1.5	7.5 + 0.5	0.80 + 0.03
SSA09	34.0 + 1.5	8.5 + 0.5	0.80 + 0.03
SSA12	54.0 + 1.5	7.5 + 0.5	0.80 + 0.03
SSA15	54.0 + 1.5	8.5 + 0.5	0.80 + 0.03
SSA20	67.0 + 1.5	9.5 + 0.5	0.80 + 0.03

OPTIONS AVAILABLE:
• Long lead (50 mm) on either side
• Extra Long Lead (65 mm) on either side.
• Thick lead (1.0 mm) on both sides.

Construction:
SSA: The resistor element is a resistive wire, which is wound, in a single layer, on a ceramic rod. Metal caps are pressed over the ends of the rod. The ends of the resistive wire and the leads are connected to the caps by welding. Tinned copper clad iron leads with poor heat conductivity are employed permitting the use of relatively short leads to obtain stable mounting without overheating. The resistor is coated with green silicon cement which is non-flammable, will not drip even at high overloads and is resistant to most commonly used cleaning solvents

Electrical Characteristics
DERATING: The power that the resistor can dissipate depends on the operating temperature



Maximum dissipation (Pmax) in percentage of rated as a function of ambient temperature (Tamb)

Application Information:
These types of resistors are typically used for the following applications:

1) Discharge resistors
2) RC Circuits
3) DC stage of power supplies to absorb the breaking energy of trains
4) Braking systems of AC Drives for elevators / lifts / cranes / trains

Test and Requirements

Essentially all tests are carried out in accordance to the schedule of IEC publications 60115-1, category 40/200/56 (rated temperature range -40 to +200 ⁰c; damp heat, long term, 56 days and along the lines of IEC publications 60068-2); 'Recommended basic climatic and mechanical robustness testing procedure for electronic components' and under standard atmosphere conditions according to IEC 60068-1 subclause 5.3, unless otherwise specified.

In some instances deviations from IEC applications were necessary for our method specified.

Table 8. Test and requirements

TEST	PROCEDURE	REQUIREMENTS
Temperature coefficient	Between - 400c and + 2000c: R < 10Ω R > 10Ω	0 to 600 ppm/ 0c - 80 to +140 ppm / 0c
Rated Load	Rated wattage for 30 minutes	+ (1% + 0.05W)
Short time overload	2.5 times the rated wattage for 5 sec	△R/Rmax + 2% +0.1
Insulation Resistance	500 V DC	31000MW
Robustness of terminations: Tensile all samples Bending half number of samples Torsion other half number of samples	Load 10 N; 10 s Load 5 N; 4 x 900 2 x 1800 in opposite directions	No visual damage △ R/Rmax + 0.5% +0.05
Solderability (after ageing)	16 h at 155 0C; leads immersed in flux 600, leads immersed 2 mm for 2 + 0.5 s in a solder bath at 235 + 5 0c	Good tinning; (>95% covered ) No Visible Damage
Resistance to soldering heat	Thermal shock: 3 s; 100c; 2.5 mm from body	△ R/Rmax + 0.5% + 0.05
Rapid change of temperature	30 minutes at - 400c and 30 minutes at + 2000c; 5 cycle	No visible damage △ R/Rmax + 1% + 0.05
Vibration	Frequency 10 to 500 Hz (1 to 7W) and 10 to 55 Hz (10 to 20W),displacement 0.75 mm or acceleration 10 g, three directions; total 6 h (3x2 h)	No visible damage △ R/Rmax + 0.5% + 0.05
Incombustibility	6 times the Rated wattage for 5 minutes	Not flammable

Get Free Quote